Enhanced sludge solubilization by microbubble ozonation

A microbubble ozonation process for enhancing sludge solubilization was proposed and its performance was evaluated in comparison to a conventional ozone bubble contactor. Microbubbles are defined as bubbles with diameters less than several tens of micrometers. Previous studies have demonstrated that microbubbles could accelerate the formation of hydroxyl radicals and hence improve the ozonation of dyestuff wastewater. The results of this study showed that microbubble ozonation was effective in increasing ozone utilization and improving sludge solubilization. For a contact time of 80 min, an ozone utilization efficiency of more than 99% was obtained using the microbubble system, while it gradually decreased from 94% to 72% for the bubble contactor. The rate of microbial inactivation was obviously faster in the microbubble system. At an ozone dose of 0.02 g O₃ g⁻¹ TSS, about 80% of microorganisms were inactivated in the microbubble system, compared with about 50% inactivation for the bubble contactor. Compared to the bubble contactor, more than two times of COD and total nitrogen, and eight times of total phosphorus content were released from the sludge into the supernatant by using the microbubble system at the same ozone dosage. The application of microbubble technology in ozonation processes may provide an effective and low cost approach for sludge reduction.     

Pre-concentration and separation of heavy metal ions by chemically modified waste paper gel

Iminodiacetic acid was immobilized on waste paper by chemical modification in order to develop a new type of adsorption gel for heavy metal ions. Adsorption behavior of the gel was investigated for a number of metal ions, specifically Cu(II), Pb(II), Fe(III), Ni(II), Cd(II), and Co(II) at acidic pH. From batch adsorption tests, the order of selectivity was found to be as follows: Cu(II)  Fe(III) > Pb(II) > Ni(II)  Co(II) > Cd(II). Column tests were carried out for pairs of metal ions to understand the separation and pre-concentration behavior of the gel. It was found that mutual separation of Ni(II) from Co(II) and that of Pb(II) from Cd(II) can be achieved at pH 3. Similarly, selective separation of Cu(II) from Cu(II)–Fe(III) and Cu(II)–Pb(II) mixtures at pH 1.5 and 2, respectively, was observed by using this new adsorption gel. In all cases, almost complete recovery of the adsorbed metal was confirmed by elution tests with HCl.     

Composition of Floating Debris in Harbours of the United States

As part of a programme to characterize floating anthropogenic debris in the aquatic environment, the US Environmental Protection Agency (EPA) conducted 18 field surveys in the harbours of major metropolitan cities of the east, west, and Gulf coasts of the United States and the Mid-Atlantic Bight. the surveys were designed to provide information on the types, relative amounts, and distributions of aquatic debris in different geographic regions of the United States. Neuston nets (0.33 mm mesh) were used to collect surface debris during outgoing tides on two or three consecutive days in selected areas of each city. After each net tow, the debris, which ranged in size from small resin pellets to large plastic sheeting pieces, was identified, categorized, and counted. the data are being used to qualitatively characterize aquatic debris in coastal metropolitan areas, to examine potential regional variations, and to tentatively identify potential sources.     

Types of Ectomycorrhiza as Pollution Stress Indicators: Case Studies in Slovenia

Mycorrhiza is the main spatial and temporal linkage between different constituents in a forest ecosystem. The functional compatibility and stress tolerance of ectomycorrhizal types is species specific, and therefore the information on the ectomycorrhizal community structure can add to the understanding of processes in forest ecosystems and can also be applied as tools for bioindication of pollution stress in forest soils. We have studied the effects of pollution (N and S) on trees and forest soils by: (1) quantification of ECM types diversity as in situ indicators in forest stands, (2) determination and quantification of pollution-sensitive or -insensitive ECM types as passive monitors, (3) root growth and development of ECM on nonmycorrhizal spruce seedlings, planted at the studied sites (active monitors), and (4) ECM infection (a bioassay based on mycorrhizal inoculum potential) of seedlings in an experimental set-up as ex situ testers. ECM species richness for Norway spruce trees (Picea abies) showed higher values in unpolluted sites than in polluted ones, while the differences were not significant for European beech trees (Fagus sylvatica). As pollution-sensitive or -insensitive ECM species in spruce forests, we suggest Hydnum rufescens (sensitive) and Paxillus involutus (unsensitive). Mycorrhizal potential in Norway spruce seedlings as a bioassay for soil N and S pollution was effective, and is suggested as an additional, standardized and widely comparable system in bioindication of soil pollution.     

汶川地震灾区过渡房安置点场地选择中的地震问题

大地震后,如何在最短的时间内在灾区选择比较安全的过渡房安置点建设场地,是一项具有挑战性的工作。本文以四川省汶川8.0级大地震后灾区群众快速安置为背景,论述了选择过渡房安置点场地必须考虑的地震问题,并提出了处理地震断层、地表裂缝、砂土液化、坍塌等实际问题的方案;利用强余震的预测结果,分析了这些灾害对场地可能造成的危害;同时对可能潜在的滑坡、危岩崩塌、泥石流等地质灾害提出相应的处理建议,供安置点规划建设参考。     

Spatial cost efficiency in waste paper handling: the case of corrugated board in Sweden

This paper analyzes the spatial cost efficiency of the Swedish legislation regarding waste disposal handling. We focus on the case of corrugated board and recognize that the different counties in Sweden possess different economic prerequisites in terms of waste paper recovery and utilization potential. We employ data for six corrugated board mills and 20 counties and a non-linear programming model to identify the least cost strategy for reaching the politically specified recycling target of a 65% recovery rate for corrugated board. That is, the total costs of recovering a minimum of 65% in each county are calculated and compared with the case when the country as a whole recovers 65% of all old corrugated board is collected but there exist no uniform target for each county. The conclusion is that from an efficiency point of view the recovery efforts should be concentrated to the highly populated and urbanized counties, and not be uniformly divided throughout the country. In the base case, the results suggest that the cost efficient county-specific recovery rates should range from 51 to 72%.     

郑州市春季大气污染过程VOCs特征、臭氧生成潜势及源解析

利用GC5000在线气相色谱仪于2018年4月15日～5月15日对郑州市城区环境大气挥发性有机物(VOCs)进行监测,开展其污染特征、臭氧生成潜势(OFP)和来源解析研究.结果表明,监测期间,郑州市春季VOCs平均体积分数为40.26×10~(-9),非污染日和污染日VOCs平均体积分数分别为35.82×10~(-9)和44.12×10~(-9),污染日相较非污染日增长23%;VOCs物种对OFP的贡献表现为烯烃芳香烃烷烃炔烃;源解析结果显示监测期间郑州市VOCs主要来源是LPG源(66.05%)、机动车源(47.39%)、工业溶剂源(37.51%)、燃烧源(37.80%)和植物排放源(11.25%),且污染日的LPG源和植物排放源的贡献率较非污染日增长22.92%和68.50%.     

羽序灯心草作为酸性矿山废弃地先锋植物潜力

生态复垦是当前世界各国酸性矿山废弃地修复的主要方法.通过研究云南来利山锡矿区废弃地土壤pH值、肥力特征及重金属含量,以及矿区生长的羽序灯心草形态特征和植株体内重金属的分布特征,分析植株耐酸性、对废弃地土壤肥力的适应性及对Zn和Cu等重金属污染的耐性,探讨其作为酸性矿山废弃地先锋植物的潜力.结果表明,研究区域根际土壤pH值均值范围为3.46～4.01,呈酸性;土壤中有机质、全钾、全磷和速效磷含量分别为10.28～25.75g·kg~(-1)、 8.84～9.32g·kg~(-1)、 0.56～0.63g·kg~(-1)和1.82～5.72mg·kg~(-1),处于较低水平;土壤中Zn、Cu和Fe含量均值范围分别为54.93～114.49、 92.53～127.59和47 133.60～112 259.63 mg·kg~(-1),其中重金属Cu含量超出风险筛选值1.85～2.55倍;研究区域羽序灯心草株高均值范围为43.77～55.42 cm,对照组植株高度为51.38～57.66 cm,无显著差异,表明羽序灯心草具有耐酸性及对重金属污染具有耐性.进一步分析对重金属Cu和Zn的富集能力和转移特征,发现对Cu和Zn都具有富集能力,且对Zn具有运转能力,具有一定的富集吸收潜力.株高与根际土壤中速效磷的含量显著相关,后期羽序灯心草作为先锋植物在矿山废弃地进行种植时,可针对性地补充含速效磷的肥料改善土壤肥力条件.综合分析结果表明,羽序灯心草作为先锋植物修复酸性矿山废弃地具有巨大潜力.     

北京南部城区PM2.5中碳质组分特征

为了解《大气污染防治行动计划》实施后北京市大气PM_2.5中碳质组分特征,于2017年12月至2018年12月在北京污染较重的南部城区进行了PM_2.5连续采样,对其中的有机碳（OC）和元素碳（EC）进行了全面研究.结果表明,北京大气PM_2.5、OC和EC浓度变化范围分别为4.2~366.3、0.9~74.5和0.0~5.5 μg ·m^-3,平均浓度分别为（77.1±52.1）、（11.2±7.8）和（1.2±0.8）μg ·m^-3,碳质组分（OC和EC）整体占PM_2.5的16.1%.OC质量浓度季节特征表现为：冬季[（13.8±8.7）μg ·m^-3] > 春季[（12.7±9.6）μg ·m^-3] > 秋季[（11.8±6.2）μg ·m^-3] > 夏季[（6.5±2.1）μg ·m^-3],EC四季质量浓度水平均较低,范围为0.8~1.5 μg ·m^-3.二次有机碳（SOC）年均质量浓度为（5.4±5.8）μg ·m^-3,四季贡献比例范围为45.7%~52.3%,年均贡献为48.2%,凸显了二次形成的重要贡献.随污染加重,尽管OC和EC贡献比例均降低,但浓度水平却成倍升高,OC和EC浓度在严重污染天分别是空气质量为优天的6.3和3.2倍.与非供暖时段相比,供暖时段PM_2.5、OC和SOC浓度分别增加了14.4%、47.9%和72.1%,体现了OC对供暖季PM_2.5污染的重要贡献.PSCF分析表明,位于北京西南的山西省和河南省部分区域是PM_2.5和OC的主要潜在源区,且PM_2.5潜在源区更为集中;EC的PSCF高值（>0.7）区域较少,主要位于北京南部,如山东省和河南省部分地区,且北京市及周边地区贡献明显.     

中国集成电路制造行业VOCs排放特征及控制对策

中国电子信息产业发展迅速,集成电路等电子器件产量不断增加.在集成电路制造的过程中,大量有机溶剂的使用导致VOCs的产生和排放,从而对大气环境造成影响.为掌握集成电路制造行业VOCs的排放特征,系统分析了其工艺流程和产排污环节,分析了行业废气收集和治理现状,通过对典型企业VOCs的排放监测,获得VOCs排放水平;采用排放因子法核算行业VOCs历史排放量,并基于行业排放特征及减排潜力分析,提出了相应的污染防治对策.结果表明：在集成电路制造中,VOCs排放环节主要集中在光刻、清洗、去胶等过程,1 m²集成电路产量约使用87 g有机溶剂,VOCs产生量较大;通过采取高效的VOCs治理技术,集成电路制造行业有组织排放水平较低,平均浓度为2.1 mg·m^-3,但厂界无组织排放浓度相对较高,平均浓度为0.78 mg·m^-3,接近国家标准的排放限值.根据排放量核算结果,2011—2016年中国集成电路制造行业VOCs排放量呈逐年上升的趋势,主要受产量增加而相应污染控制技术水平提升有限的影响,无组织排放量比重大,占排放总量的38.1%~45.1%.